Community for Kel-Tec Shooters banner

1 - 17 of 17 Posts

·
Registered
Joined
·
6 Posts
Discussion Starter · #1 ·
Hi all. I dont know if this is the appropriate place to post this but I was looking to purchase some of those washers for my p3at. Can someone point me in the right direction? Thanks in advance.
 

·
Registered
Joined
·
5,567 Posts
You'll need 22 more posts to have access to the Trading Post. ;)

If you do a search of the TP you should be able to find the old thread with them for sale.

Welcome to KTOG

CJ
 

·
Registered
Joined
·
14,984 Posts
princemorr2003, I would suggest you consider the posts in this thread and NOT part with any washers ...

that slide NEEDS to be replaced. washers will do no good.
 

·
Registered
Joined
·
14,984 Posts
Nakanokalronin said:
I had my slide replaced and then added a washer to the new slide for insurance.
that is the ticket. me too.

but to use the buffer to try to fix an existing problem is not a good idea. get it fixed first. then add the insurance policy.
 

·
Registered
Joined
·
1,553 Posts
autobahn said:
Still confused.

What is the washer for?
Hi,

It prevents the recoil guide spring rod from peening the hole on the front of the side which will eventually allow the recoil springs to poke through. This is not an issue on any of the P3AT's that I have shot or worked on.

Best Regards
 

·
Registered
Joined
·
36 Posts
Is there a list anywhere of the serial# range that has the peening problem, or is this information unknown?
 
G

·
menocu said:
Is there a list anywhere of the serial# range that has the peening problem, or is this information unknown?
http://www.ktog.org/cgi-bin/yabb2/YaBB.pl?num=1189138280/0#5

JFB said:
UPDATED
Slide peening serial numbers -- 1,000 from J0000 (calc # week's production) -- estimated (CWAG) or actual manufactured date

HZUXX  --  xx --*7/20/06
JODXX --1.4-- 8/7/2006 CWAG  *7/27/06
JONXX --2.2-- 8/14/2006 CWAG
J26XX --7.4-- 9/11/2006 CWAG
J2AXX  --7.8--9/15/2006 CWAG* 09/06
J3QXX  --12.6--*10/20/2006  
J4RXX  -- 16.1--11/20/2006 CWAG
J5DXX  --18.3--12/4/2006 CWAG
J5KXX  --18.9--12/7/2006 CWAG
J5HXX  *12/05/06
J65XX  --20.9--*12/13/2006
J6HXX  --22.0--12/18/2006 CWAG
J7CXX  --25.0--*1/12/07
J87XX  *02/2507
J8DXX  
J8UXX  --30.0--*02/26/07
J9XXX -- 30.6  -- 03/01/07 CWAG
JAFXX -- 35.4 --  04/05/07 CWAG

*  Kel-tec verified manufacture date.
 

·
Registered
Joined
·
36 Posts
Thanks much for the list, looks like I should be ok. Was afraid I might have just wasted time and money on plating for a slide that's going to go back to KT.
 
1 - 17 of 17 Posts
Top