Community for Kel-Tec Shooters banner
1 - 8 of 8 Posts

·
Read Only
Joined
·
10 Posts
Discussion Starter · #1 ·
Anyone happen to know if there's a way to convert the Beretta/S&W versions to a Sigp320/250 magazine with the mag catch like you can do with the P226?

Or have they mentioned anything about magazine compatibility of the supposed "multi-mag" version I keep hearing about?
 

·
Premium Member
Joined
·
17,775 Posts
The Gen 1 was officially compatible with SIG226, B92/96, S&W 59 series, and Glock 17/22 versions. The Gen 2 has been made to work with Glock 17/22, S&W M&P, and hopefully Beretta92/96 and SIG 226 versions. Your best bet would be to do like everybody else has been doing for the past 20 years and physically compare your intended magazine with one it is already made for and see if they are close enough to work. There is no provision to make it "multi-mag" compatible like you are asking to the best of my knowledge. And the 320 is new enough on the market there just aren't enough out there for anyone to have tried it. Someone may have tries it with the 250 but I really can't recall.
 

·
Premium Member
Joined
·
15,000 Posts
CJ, Kel Tec IS coming out with what they're calling a "multi mag" version of the sub2000...not sure if it will be "gen3" or what?

I have this from Nick at KT...."Same as before once a glock always a glock, but the multi mag that is coming out can be changed to fit different mags but its in the magcatch."

Also found this:

Kel-Tec is also updating their hugely-popular pistol caliber carbine line-up with the new Sub-2000 Multi Mag. The Sub-2000 Multi Mag accepts Smith & Wesson M&P magazines as well as Beretta 92 and SIG 226 magazines with adapter kits. The updated carbines will be chambered for 9mm Luger and .40 S&W and the MSRP will remain $500, while the kits will list between $30 to $50 and should be available very soon.
https://www.gunsamerica.com/blog/ke...3g&utm_campaign=/blog/kel-tec-shot-show-2016/



.
 

·
Registered
Joined
·
607 Posts
Just got a Gen2, Glock version. It really didn't matter, even though I have no Glocks. It's just too sweet to pass up. Wanted to be compatible with the P11, but oh well.
I had considered the mag-catch change if others were available. Hopefully, others will be able to utilize their Sig, Berreta, SW, etc, but to me....don't matter.
 

·
Premium Member
Joined
·
17,775 Posts
CJ, Kel Tec IS coming out with what they're calling a "multi mag" version of the sub2000...not sure if it will be "gen3" or what?

I have this from Nick at KT...."Same as before once a glock always a glock, but the multi mag that is coming out can be changed to fit different mags but its in the magcatch."
Hmm. Almost sounds like Gen 1 part deaux..... ;)
 

·
Registered
Joined
·
886 Posts
That was then...this is now. The days of non ending freebies are pretty much over.
I'm ok with that as long as parts are available. I asked to pay but the nice lady on the phone said they would just ship it to me at no cost. I think at the time the needed parts for the conversion were less then $10 though instead of the estimated $30 to $50 for the Gen2 parts.
 
1 - 8 of 8 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top