Community for Kel-Tec Shooters banner
1 - 12 of 12 Posts

·
Registered
Joined
·
13 Posts
Discussion Starter · #1 ·
I having real problems with the site. It won't let me access any of the pages between 5 and 293. I am looking for some info on slide on grips. If anyone can shed some light on this I'd appreciate it.
 

·
Registered
Joined
·
13 Posts
Discussion Starter · #4 ·
I found a picture of the Uncle Mikes grip. It looks like what I'm after. Howevre that particular site only offered Med, and Large. I'd guess I'd need small. I couldn't find the product on Uncle Mikes own website. Did they discontinue?
 

·
Premium Member
Joined
·
1,830 Posts
Grips for the Kel-Tec P-3AT

Hogue, Pachmayr, and Glaser, make slip-on grips that fit the P-3AT. They are all a bit different. Some may need trimming. Glaser also makes “pads” that stick to the front and/or back straps to soften and slightly enlarge the grip. AGRIP and TractionGrips makes a pre-cut stick-on grip.

Hogue HandAll, Jr
These have finger grooves, are thinner at the front and back straps, have slight palm swells, and are textured on the sides. These tend to be a bit loose on the P3-AT, so a layer or two of bicycle tube or a bit of something sticky helps to keep them tight.
http://www.brownells.com/aspx/NS/store/productdetail.aspx?p=6938&s=

Pachmayr, Model 4
These have finger grooves, are the same thickness all around, and are textured all over. These tend to be a bit loose on the P3-AT, so a layer or two of bicycle tube or a bit of something sticky helps to keep them tight.
http://www.pachmayr.com/slip-on-grips.php

Glaser
These grips have no finger grooves, are the same thickness all around, and are smooth all over.
The pads are self-adhering and can be removed easily.
http://www.ktaddons.com/

AGRIP
http://www.brookstactical.com/Pages/fitlist.html

Tractiongrips
http://www.tractiongrips.com/

Or you can make your own:
One good thing about doing it this way is that the material is thin and you can experiment by trying a different number of layers. Some bike tubes have ribbed areas, so you can make a ribbed or smooth grip.
I got a couple of tubes free - went to a local bike shop and asked for any bad ones they were throwing away.
The 20 x 1.75 - 2.125 worked best for me.
http://www.ktrange.com/articles/a7/a7.html

Bobo
 

·
Registered
Joined
·
13 Posts
Discussion Starter · #8 ·
Thanks You guys are great! Now that I've finished my F&B, ordered a trigger shoe and grip extension, pretty soon my P3 AT will be a little hummer. The sheriff's office just notified me to come in and pick up my carry permit. Now I need to take it out and hammer some more rounds through it until I've got it down pat. Many thanks!
 

·
Registered
Joined
·
5,567 Posts
Use caution if you install the trigger shoe on your P3AT:

Sangueffusor said:
It was made for the P-11 which has a wider trigger guard, so it will stick out on the sides of the P3-AT's trigger guard, possibly causing unintentional discharge when holstering. You could narrow it yourself, though.
I used 2 layers of shrink tube on my PF9's trigger, it feels much better now and my finger pad dosen't sting after I shoot.

CJ
 

·
Registered
Joined
·
13 Posts
Discussion Starter · #12 ·
To access additional pages look on the page number line. There are two drop down icons there that bring up additional pages in blocks of 10 pages at a time. You'll find a host of information on grips and everything else you can thnik up just keep looking.
 
1 - 12 of 12 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top